Martin Roboscan Pro 1220 Návod k obsluze

© 1995-1996 Martin Professional A/SRoboscan Pro 1220operator’s manualPart# 510061

10 Roboscan Pro 1220 - operator’s manualFitting the Mains PlugThe Roboscan Pro 1220 is delivered from the factory without a plug on the mains cable. Y

Roboscan Pro 1220 - operator’s manual 11© 1995-1996 Martin Professional A/SFitting the Mounting BracketThe mounting bracket is already fitted onto the

12 Roboscan Pro 1220 - operator’s manualsection 3OPERATING VIA ALIGHTING CONTROLLERAll effects in the Roboscan Pro 1220 are fully DMX 512 and Martin R

Roboscan Pro 1220 - operator’s manual 13© 1995-1996 Martin Professional A/SThe above figure shows the cable to connect from 5-pin DMX output to 3-pin

14 Roboscan Pro 1220 - operator’s manualThe control module on the front end of the Pro 1220 allows you to set the DMX protocol and assignthe fixture a

Roboscan Pro 1220 - operator’s manual 15© 1995-1996 Martin Professional A/Ssection 4REMOTELY CONTROLLABLEFUNCTIONSThis section briefly describes the v

16 Roboscan Pro 1220 - operator’s manualCOLOR WHEELS (PRO 1220 CMYR AND RPR ONLY)The Pro 1220 CMYR has two separate and overlapping color wheels each

Roboscan Pro 1220 - operator’s manual 17© 1995-1996 Martin Professional A/SDIMMER / SHUTTERHigh resolution, 0 to 100% smooth dimming is provided by th

18 Roboscan Pro 1220 - operator’s manualsection 5THE PRO 1220 CONTROL MODULEThe control module on the front end of the Pro 1220 offers several feature

Roboscan Pro 1220 - operator’s manual 19© 1995-1996 Martin Professional A/SPSEt - Protocol SetupAfter switching on a Pro 1220, it will automatically d

© 1995-1996 Martin Professional A/S, Denmark.All rights reserved. No part of this manual may bereproduced, in any form or by any means, withoutpermiss

20 Roboscan Pro 1220 - operator’s manualUse the arrow keys to toggle between on and off. Select 'on', by pressing [enter], if wish the proto

Roboscan Pro 1220 - operator’s manual 21© 1995-1996 Martin Professional A/SSP 1 to SP16Up to 16 special service and adjustment sequences are available

22 Roboscan Pro 1220 - operator’s manualErrAThe 'A-Module Error' indicates that there is no communication between the serial data receivermo

Roboscan Pro 1220 - operator’s manual 23© 1995-1996 Martin Professional A/Ssection 6HARDWARE SETTINGS ANDADJUSTMENTS The Roboscan Pro 1220 comes fully

24 Roboscan Pro 1220 - operator’s manualREPLACING A MODULETo replace the module simply reverse the steps above being careful when you replace the modu

Roboscan Pro 1220 - operator’s manual 25© 1995-1996 Martin Professional A/SLamp Replacement and AdjustmentTo reduce the risk of the lamp shattering it

26 Roboscan Pro 1220 - operator’s manualHMI 1200 LAMP1.Locate the 3 adjustment screws on the back of the lamp module and turn all three of them asmuch

Roboscan Pro 1220 - operator’s manual 27© 1995-1996 Martin Professional A/SAdjusting the Pan/Tilt StopsRe-adjusting the mechanical stop on the Robosca

28 Roboscan Pro 1220 - operator’s manual5. Reset the Roboscan Pro 1220 a number of times to check the accuracy of the new reset posi-tion. 6. Again, s

Roboscan Pro 1220 - operator’s manual 29© 1995-1996 Martin Professional A/SIf the dampers are set to a position that is too tight you will find that i

Roboscan Pro 1220 - operator’s manual 3© 1995-1996 Martin Professional A/Ssection 1INTRODUCTIONThe Roboscan Pro 1220 features . . . . . . . . . . . .

30 Roboscan Pro 1220 - operator’s manualsection 7MAINTENANCETo ensure optimum and uninterrupted performance from the Pro 1220 it is important to keep

Roboscan Pro 1220 - operator’s manual 31© 1995-1996 Martin Professional A/Sappendix aDMX PROTOCOLDMX Channel OffsetDMXValue EffectPro 1220 CMYR - mode

32 Roboscan Pro 1220 - operator’s manual-2-0 -10 -20 -30 -40 -50 -60 -70 -80 -90 - 9798 - 105106 - 113114 - 121122 - 129130 - 137138 - 145146 - 153154

Roboscan Pro 1220 - operator’s manual 33© 1995-1996 Martin Professional A/S7340 -20 -40 -60 -80 -100 -120 -140 -160 -180 - 188189 - 196197 - 204205 -

34 Roboscan Pro 1220 - operator’s manual12 - -0 - 4950 - 99100 - 149150 - 255Prisms, Frost (Pro 1220 CMYR)Open3-Facetfrost5-Facet-8-0 - 4243 - 8485 -

Roboscan Pro 1220 - operator’s manual 35© 1995-1996 Martin Professional A/S- - 15 17 - - 11 13 - - 13 1501 - 251252 - 255Speed: Pan, TiltTrackingSpeed

36 Roboscan Pro 1220 - operator’s manualappendix bSPECIAL SEQUENCESSequence Scene DescriptionSP 1 RESET ALLSP 2LAMP/OPTO ADJUST (Lamp On) - PRO 1220 C

Roboscan Pro 1220 - operator’s manual 37© 1995-1996 Martin Professional A/SSP 6PAN/TILT ADJUST (Lamp On)St 1 NeutralSt 2 Pan RightSt 3 Pan LeftSt 4 Ti

38 Roboscan Pro 1220 - operator’s manualSP10LOCATING ROTATING GOBO INDEX (Lamp On)St 1 Open Gobo SelectedSt 2 Selecting Gobo 1 and IndexingSt 3 Select

Roboscan Pro 1220 - operator’s manual 39© 1995-1996 Martin Professional A/Sappendix cTECHNICAL SPECIFICATIONSRoboscan Pro 1220 CMYR / XR / RPRDimensio

4 Roboscan Pro 1220 - operator’s manualsection 6HARDWARE SETTINGS ANDADJUSTMENTSRemoving and Replacing Modules . . . . . . . . . . . . . . . . . . . .

Roboscan Pro 1220 - operator’s manual 5© 1995-1996 Martin Professional A/Ssection 1INTRODUCTIONCongratulations on your choice of the Roboscan Pro 1220

6 Roboscan Pro 1220 - operator’s manual• Fixed and rotating gobos can be combined.DIMMER / SHUTTER• High-speed shutter (2 to 16 Hz) for instant black-

Roboscan Pro 1220 - operator’s manual 7© 1995-1996 Martin Professional A/SAbout this ManualThis user's manual covers Pro 1220 CMYR / XR fixtures

8 Roboscan Pro 1220 - operator’s manualsection 2INSTALLING THE PRO 1220The Roboscan Pro 1220 is delivered fully prepared from the factory so only a fe

Roboscan Pro 1220 - operator’s manual 9© 1995-1996 Martin Professional A/Scarefully insert it into the lamp socket.6. Again, without touching the glas